Menu

Radiant Floor Heating: Warmth That Starts at Your Feet

Heat rises. That single fact explains why radiant floor heating feels different from forced-air systems the moment you walk into a room. Instead of blowing warm air near the ceiling and letting it drift down, radiant heating warms the floor surface directly and lets that warmth spread evenly upward through the space. The result is a room that feels comfortable at a lower thermostat setting, with no drafts, no cold spots near the floor, and no dust blowing through vents.

At Thorsen’s-Norquist , we install and service radiant floor heating for homeowners and businesses that want steady, quiet comfort. Whether you are building new, remodeling a bathroom, or looking to replace an aging heat source, we can help you decide if radiant floor heating fits your project, your budget, and the way you use your space.

Common Questions People Ask Before They Start

Most people who call us about radiant floor heating have the same few concerns. The first is cost. Radiant systems usually cost more to install than a standard furnace-and-duct setup, but they often cost less to operate because they heat efficiently and evenly. We take our responsibility very seriously when you place your trust in us, so we pledge to always tell you up front what your cost will be to complete your job correctly. You will not be surprised by hidden charges after the work is done.

The second common question is whether radiant heating works with existing flooring. The answer depends on the floor material and the type of system. Tile and stone are excellent conductors and pair beautifully with radiant heat. Engineered wood, laminate, and certain vinyl products also work well when the system is designed correctly. Thick carpet and heavy padding can slow heat transfer, so we make it a point to go over any details or limitations of the proposed system that will affect your enjoyment of the end result before we begin.

The Two Main Types of Radiant Floor Heating

Radiant floor heating comes in two primary forms, and choosing between them depends on the size of the area, the flooring, and whether the project is new construction or a retrofit.

  • Hydronic systems: These circulate warm water through flexible tubing installed beneath the floor. Hydronic radiant heat is the most economical choice for heating large areas or whole homes. A boiler or water heater warms the water, and a pump moves it through the loops. Operating costs are typically low, which makes this option attractive for whole-house heating.
  • Electric systems: These use electric resistance cables or mats installed under the floor. Electric radiant heat is ideal for smaller spaces such as bathrooms, kitchens, and mudrooms, or for warming a single room that stays uncomfortably cold. Installation is simpler, which makes electric systems a good fit for remodels where tearing up large areas is not practical.

During the planning stage, we help you weigh the trade-offs. Hydronic systems cost more up front but reward you with lower monthly operating expense over many years. Electric systems cost less to install but draw more to run over large areas. The right choice comes down to how much floor area you want to heat and how you plan to use each room.

How the Installation Process Works

A quality radiant floor installation follows a careful sequence. Skipping steps leads to uneven heating and callbacks, so we do the work in order.

  1. Assessment and design: We measure the space, review the flooring, calculate heat loss, and design a loop or mat layout that delivers even warmth without hot or cold zones.
  2. Subfloor preparation: We make sure the subfloor is clean, level, and ready to accept the tubing or cables. Insulation is added below the system so heat travels up into the room instead of down into the ground.
  3. Installation and testing: We lay out the tubing or mats, connect the manifold or controls, and pressure-test hydronic loops or verify electrical resistance before any flooring goes down. Testing before covering is critical because repairs are far harder afterward.

Once the system passes testing, the finished flooring goes in place and the thermostat and controls are set. We walk you through how to operate the system so you get the most comfort for the least energy.

Where Radiant Floor Heating Makes the Biggest Difference

Bathrooms are the most requested project because a warm tile floor on a cold morning is a genuine luxury. Kitchens benefit for the same reason, since people stand on hard surfaces for long stretches. Basements, which tend to feel damp and chilly, become usable living space once the floor is warm. Sunrooms and additions that never connected well to the main heating system finally hold a steady temperature.

Radiant heat also serves commercial spaces, entryways, and showrooms where quiet, even warmth improves the experience for everyone who walks in. Because there are no blowers or vents, the system runs silently and keeps airborne dust to a minimum, which appeals to anyone sensitive to allergens.

Thorsen’s-Norquist serves customers throughout Modesto and Turlock, CA. If you are considering radiant floor heating for a new build, a remodel, or a single room that never gets warm enough, reach out and we will help you plan a system that fits your space and delivers comfort for years to come.

Radiant Floor Heating Turlock, CA, Keyes, CA, Denair, CA, Hughson, CA, Ceres, CA & Cortez, CA

Radiant Floor Heating in Turlock, CA

Radiant Floor Heating ∴ Delhi, CA ∴ Hilmar, CA ∴ Empire, CA

carrier factory authorized dealer

Carrier Eco Home

Nate Certified Technicians

Navien

Geothermal Comfort Systems

We Sell Energy Star

old filmstrip of historical photos

Taking Care of Our Community

Since 1911

Delhi, CA

Atwater, CA

Winton, CA

Cortez, CA

Waterford, CA

Delhi, CA

Denair, CA

Livingston, CA

Riverbank, CA

Ceres, CA

Salida, CA

Turlock, CA

Denair, CA

Empire, CA

Keyes, CA

Hughson, CA

Hilmar, CA

Oakdale, CA

Modesto, CA